Essential Plumber Tips for Bathtub Installation
Essential Plumber Tips for Bathtub Installation
Blog Article
Here down the page you can find some wonderful information and facts with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Mounting a tub isn't precisely brain surgery, however it does need solid plumbing, carpentry, and also sometimes, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately hard job. If the old tub is conveniently accessible, the project can relocate quickly; if you have to open a wall surface to get rid of the old tub and also position the new bathtub, the job is much harder. In either case, the project is within a home handyman's abilities, although you will require a helper to leave the old tub and set in the brand-new one. Make sure you have qualified yourself for the job and also fit attempting it. As opposed to working with a professional to take control of a halfway-completed task, it is far better to take into consideration utilizing one prior to you start. Opportunities are you may require a specialist plumber to make tube connections.
This short article will certainly assist you mount a brand-new tub in your bathroom if you have currently bought a brand-new tub and do not require to alter the plan of your previous water system pipes.
Your tools and material list should consist of the following:
Planning for the Installation
To start with, the supporting framework supplied with the bathroom ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is very important to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets device to stop strain on the bathtub.
Fit the versatile faucet ports to the bottom of both taps using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath should currently be ready to be suited its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The procedure of removing the existing faucets can be fairly bothersome because of the limited accessibility that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly come from the pipelines. Once the supply pipelines have been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old sealing compound.
Before carrying on to fit the new taps, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Making use of both wood boards under its feet, position the bathtub in the required setting. The wood boards are handy in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto 4 little points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the bathtub up until the level reviews level.
To install faucets, fit all-time low of the outermost flexible faucet connector to the proper supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Activate the water system and also examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill up the tub as well as also check the overflow outlet and also the typical outlet for leaks.
Finally, take care of the bath paneling as described in the maker's instruction manual. Tiling as well as securing around the bathtub needs to wait up until the tub has been made use of a minimum of when as this will settle it into its final position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet and also the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in area between the faucet and also the sink. Secure the tap in position with the maker offered backnut. Once the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet ports. The previous kind should be connected to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bath fulfills the floor tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the installation can move enough to fracture a stiff seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, resulting in complications with dampness and possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures as well as installations. They are offered in tubes as well as cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to enable the movement experienced when the bathtub is in usage. The sealer can split fairly early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or water-proof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

We were shown that write-up about How to Install a Bathtub Yourself through an acquaintance on another web address. You should take the time to distribute this blog if you appreciated it. I thank you for reading our article about Installing A Bathtub.
Fast and effective, call! Report this page